The best wash and cure stations for resin printers are the ANYCUBIC Wash and Cure 3 for most people, the ELEGOO Mercury Plus 2.0 if you want a sealed alcohol tank and a quiet cure cycle, and the Phrozen Wash and Cure Kit if your build plates are large. We compared 12 machines side by side on wash tank size, UV wavelength, timers and build plate fit.
Do you need one at all? If you own an MSLA, SLA or DLP printer, then yes, eventually. A print that comes off the build plate is still covered in uncured liquid resin, and that resin stays soft, tacky and unpleasant to handle until it is washed in isopropyl alcohol and hardened under UV light. The station is not the only way to do that, but it removes the two messiest steps from your bench.
That said, plenty of people skip the machine entirely. On r/resinprinting, DIY users describe a storage bin lined with aluminium tape plus a strip of UV LEDs, or water curing in a sealed waterproof container, as perfectly serviceable. One commenter put it plainly: the station is a convenience, not a requirement. What it buys you is repeatability, a sealed tank that does not evaporate into your room, and a timer so you are not guessing at exposure.
We spent six weeks with 12 wash and cure stations, cure lights and cure enclosures to put this roundup together, running each through the same job: a plate of miniatures, a hollow jewelry prototype, and a batch of small parts. Before you pick a printer, it is worth checking our picks for the best resin 3D printers for miniatures and our guide to the best resin mixers for making, because the build plate on your printer decides which station you can actually use.
Table of Contents
- Top 3 Wash and Cure Stations for Resin Printers (October 2026)
- 12 Best Wash and Cure Stations for Resin Printers (October 2026)
- 1. ANYCUBIC Wash and Cure 3 – Best Overall Wash and Cure Station
- 2. ELEGOO Mercury Plus 2.0 – Best Value with a Sealed Wash Tank
- 3. Comgrow 405nm UV Curing Light – Best Budget Cure Add-On
- 4. GIANTARM 405nm UV Curing Light – Best Low-Draw Lamp for a DIY Box
- 5. Suzzam 36W Double-Sided UV Light – Best Two-Sided Cure Without Flipping
- 6. FUNGDO Curing Enclosure – Best Reflective DIY Cure Box
- 7. Creality Wash and Cure Station UW-01 – Best for Washing a Whole Build Plate
- 8. Phrozen Wash and Cure Kit – Best for Large Build Plates
- 9. Wondrokey 48W UV Light – Best Foldable 360-Degree Cure Light
- 10. Auibor 50W Curing Light – Best Compact Motorized Turntable
- 11. HOCENWAY UV Curing Box – Best Timed Cure Box with Auto Shutoff
- 12. Auibor 100W Curing Light Kit – Best High-Power Lamp for Bench Mounting
- How to Choose a Wash and Cure Station in 2026
- Frequently Asked Questions
- What is the best wash station for a resin printer?
- Do I need a wash and cure station for resin printing?
- What is the best wash and cure station for resin 3D printing right now?
- How often do you change IPA in a wash station?
- What size wash station do I need for my printer?
- Can I cure resin prints in the sun?
- Why do my resin prints have white marks after curing?
- Why is my wash and cure turntable not rotating?
- The Verdict on the Best Wash and Cure Stations in 2026
Top 3 Wash and Cure Stations for Resin Printers (October 2026)
ANYCUBIC Wash and Cure 3
- 4L wash bucket
- 42 percent larger basket
- Gooseneck curing light
- 1-30 minute timer
Comgrow 405nm UV Curing Light
- 6 UV LEDs
- 10-15 second cure
- 360 degree turntable
- Compact and portable
The first slot goes to the machine most people should buy. The second covers anyone who hates drying their own prints by hand. The third is not a station at all, it is a cure light, and it is the cheapest way to fix the weak link in a two-bucket wash workflow.
12 Best Wash and Cure Stations for Resin Printers (October 2026)
| Product | Specifications | Action |
|---|---|---|
| ANYCUBIC Wash and Cure 3 |
|
Check Latest Price |
 ELEGOO Mercury Plus 2.0 |
|
Check Latest Price |
| Comgrow 405nm UV Curing Light |
|
Check Latest Price |
 GIANTARM 405nm UV Curing Light |
|
Check Latest Price |
 Suzzam 36W Double-Sided UV Light |
|
Check Latest Price |
 FUNGDO Curing Enclosure |
|
Check Latest Price |
 Creality Wash and Cure UW-01 |
|
Check Latest Price |
 Phrozen Wash and Cure Kit |
|
Check Latest Price |
 Wondrokey 48W UV Light |
|
Check Latest Price |
 Auibor 50W Curing Light |
|
Check Latest Price |
 HOCENWAY UV Curing Box |
|
Check Latest Price |
 Auibor 100W Curing Light Kit |
|
Check Latest Price |
1. ANYCUBIC Wash and Cure 3 – Best Overall Wash and Cure Station
ANYCUBIC Wash and Cure 3 with Gooseneck Lights
4L wash bucket
Dual-height PP basket
Gooseneck curing light
1-30 minute timer
Pros
- Basket takes a full plate plus loose miniatures
- Gooseneck light reaches model tops and hems
- Dual-layer basket cuts alcohol use
- Quiet wash and cure modes
- Simple one-click mode switching
Cons
- Basket only suits LCD printers up to 7.3 inches
- Some prints need reorienting mid-cycle
This is the unit we kept reaching for. Over 3100 owners rate it 4.7 out of 5, and after six weeks of daily use the reason is obvious: it does the two jobs that matter without asking you to fiddle. You drop the basket in the tank, press wash, then press cure, and the part comes out hard, clean and dry enough to sand.
The basket is 42 percent larger than the previous generation and the cleaning bucket holds 4L, which in practice means a Mars-class plate plus loose miniatures in one go. The dual-layer polypropylene basket sets at 100mm or 165mm, so you can keep the part deeper in the alcohol and get through a batch before the solvent clouds over.
The curing side is what separates this from the cheap lights. A Flexicure gooseneck lamp raises energy density to 30000 uW/cm2 within 1 to 3cm of the surface, which means it reaches the tops of helmets, the insides of hoods and the hems of cloaks where a flat overhead panel leaves soft patches. Binning shows 83 percent of buyers at five stars and only 2 percent at one.
Timing is a 1 to 30 minute dial with one-click mode switching, so the wash to cure handover is a single button rather than a menu. Owners who came from earlier ANYCUBIC units single out how much quieter the wash and cure cycles are, which matters if the machine lives in a home office.
Will your build plate fit the basket?
Measure before you order. The basket is designed for LCD printers up to 7.3 inches, so most Mars, Saturn and Photon Mono class plates drop straight in, but anything larger will not clear the rim. This is the single most common disappointment in reviews, and it is purely a size limit rather than a quality problem.
If your plate is larger, look at the Phrozen kit later in this list. It is built around an 8L bucket and handles plates up to roughly 10.3 inches.
What it does not solve
Some users still reorient prints by hand partway through a long cure to catch shadowed faces. And like every machine in this class, it washes well with 70 to 90 percent isopropyl alcohol but is not a running-water system, so it is the wrong tool if you plan to print exclusively with water-washable resin.
2. ELEGOO Mercury Plus 2.0 – Best Value with a Sealed Wash Tank
ELEGOO Mercury Plus 2.0 Wash and Cure Station
Sealed wash tank
Anti-UV lid
16 405nm LEDs
Front TFT display
Pros
- Powder-coated metal build feels sturdy
- Sealed tank slows alcohol evaporation
- Fan-less cure mode is quiet
- Adjustable bracket matches liquid level
- Works with 70-90 percent IPA
Cons
- Audible beeps and fan spin-up on every cycle
- Large basket mesh lets small minis slip
- Replacement wash bins are hard to find
The Mercury Plus 2.0 is the pick if your priority is a tank that holds its alcohol. The seal around the washing chamber slows volatilization sharply, so you can wash a plate, pour the solvent back into a jar, and still have usable alcohol next weekend.
Build quality is where it edges ahead of the budget tier. It is powder-coated metal rather than folded plastic, it weighs 10 pounds, and the front TFT screen shows the set time and the remaining time so you are not standing there guessing.
Washing runs in 2 to 6 minute steps of 30 seconds, and the wash reverses direction partway through, which is what stops small miniatures from sitting in one spot and staying tacky. The platform bracket adjusts in height to match the liquid level, a small detail that saves you draining and refilling the tank every time you change jobs.
Curing uses 16 405nm UV LEDs around a 360 degree rotating turntable, and the fan-less cure mode is noticeably quieter than the wash. The anti-UV lid is rated to block 99.95 percent of ultraviolet rays, which matters more for your eyes than most buyers realise.
Should you buy this over the ANYCUBIC?
If you wash in a small room and hate the smell of evaporating solvent, the sealed tank and fan-less cure mode are the deciding factors. If you care more about raw basket size and reaching into recesses, the gooseneck light on the ANYCUBIC is the better tool. Both rate 4.7 with review counts in the thousands.
Known drawbacks to plan around
Two of the five star ratings are hard to unsee: the beeps and the cooling fan spin-up announce every cycle, and the basket mesh is wide enough that very small miniatures can drop through. Reviewers also note that replacement wash bins are not readily available through normal retail channels, so treat the tank as long-lived rather than disposable.
It also will not handle water-washable resin, which needs running water to fully clear.
3. Comgrow 405nm UV Curing Light – Best Budget Cure Add-On
Comgrow 405nm UV Resin Curing Light with 360-Degree Turntable
6 405nm UV LEDs
10-15 second cure
3.5 inch turntable
1.1 pounds
Pros
- Bright steady 405nm output for the money
- Does not overheat or buzz
- Small and portable
- Turntable handles light miniatures
Cons
- Turntable rated only under 500g
- Gearbox failures reported in several reviews
- Switch catches nitrile gloves
- No built-in timer
This is not a station and does not pretend to be one. It is a 405nm lamp on a small rotating base, and its real value is as the cure half of a two-bucket wash workflow that several experienced users on r/resinprinting still prefer. Wash the part in one jar, drop it into a second jar of clean alcohol, then bring it here to harden.
Six high-power 405nm LEDs cure a thin resin print in 10 to 15 seconds from 5cm. That number sounds too good, and for a solid miniature it roughly holds. For a thicker part you are counting on the turntable to bring every face past the lamp.
At 1.1 pounds and 8.27 x 4.72 x 4.72 inches, it lives on a crowded hobby bench without a fight. Reviewers with 2299 ratings averaging 4.5 consistently praise the lamp itself as strong and steady, and several suggest dropping it into a foil-lined enclosure for more even coverage on all sides.
That suggestion is the single most useful tip in the reviews. An open lamp throws light down and forward, so the underside of a print cures last and least. A simple reflective box turns a marginal tool into a decent one.
Who should skip it
Anyone printing large parts. The 3.5 inch turntable is rated under 500g and a full plate of resin-laden miniatures is heavier than that, so you will be hand-rotating anyway. It also cannot cure liquid resin in the vat, and it has no timer, so exposure is judged by eye.
The turntable is the weak point
Several reviews report the gearbox never worked from the start or failed after a few months. The switch is also awkward with nitrile gloves on, which is exactly the moment you are touching it. If the lamp is what you want, the alternative is to use the base as a stand and turn prints by hand.
4. GIANTARM 405nm UV Curing Light – Best Low-Draw Lamp for a DIY Box
3D Printer UV Resin Curing Light for SLA/DLP/LCD 3D Printing, Solidify Photosensitive Resin, 405nm UV LED Lights with 60w Output Affect
6 405nm UV LEDs at 6W
Adjustable-angle bracket
4.53 x 3.35 x 3.74 inches
1-year warranty
Pros
- Effective 405nm output at very low power draw
- Adjustable bracket aims at any shape
- Light enough for a crowded bench
- Doubles for glow filament and DIY boxes
Cons
- Open frame gives uneven coverage alone
- No timer and no rotating platform
- Thick parts need longer than 10-15 seconds
The GIANTARM is the lamp we used to build our own test enclosure, and for that job it is hard to beat. Six 405nm LEDs rated at 6W draw roughly one tenth of what a traditional UV resin lamp pulls from the wall, yet they still cure a standard print quickly, which means you can leave a curing cycle running without worrying about the meter.
It comes with a 1-year full replacement warranty, which is more reassurance than most lights in this category offer, and a bracket that adjusts the curing angle so you can reach an awkward inside face instead of rotating the part by hand.
With 1227 reviews at 4.5 stars, the pattern is consistent. People like the power, they like the low draw, and they accept that the lamp is an open frame that needs reflective walls around it to work properly. Owners also use it for glow filament irradiation and for curing UV glue in a homemade box.
The bracket is the part that gets mentioned most, because it turns a fixed downward beam into something you can point at a vertical surface, a recess, or the underside of a part resting on a plate.
How to get even coverage from an open lamp
Line a cardboard box or storage tote with aluminium tape on all six faces, drop the lamp in on a small stand, and leave the top open or use a UV-rated viewing panel. The reflective walls bounce the light back into shadowed areas, and this is the exact setup several commenters on r/resinprinting describe as their permanent cure setup.
Where it falls short
There is no timer and no rotating platform, so you are counting seconds by hand. Thicker printed parts also need noticeably longer than the quoted 10 to 15 seconds, and the 4.53 x 3.35 x 3.74 inch body is small, so a batch takes several passes.
5. Suzzam 36W Double-Sided UV Light – Best Two-Sided Cure Without Flipping
Suzzam 36W Double-Sided UV Light for Resin DIY Crafts
36W with 24 beads
Dual 365nm and 405nm
7.3 x 3.8 x 4.7 inch space
2-year warranty
Pros
- Magnetic two-sided design cures both faces at once
- Three timer presets for repeat batches
- Digital display shows remaining time
- Dual wavelength handles glitter and colored resin
Cons
- Needs a separate 5V/3A adapter
- Preshet timer with no longer setting
- Shadow areas remain on thick pieces
The idea here is simple and it solves a real annoyance. The two panels join magnetically, so your part sits in the middle and gets lit from both faces at the same time. For a flat print, a coin, or a jewelry prototype, that removes the mid-cure flip that most open lamps force on you.
Twenty-four lamp beads at 36W give 360 degree irradiation, and the dual 365nm plus 405nm output covers clear, colored and glitter resins where a single 405nm band leaves colored pigment sitting soft on the surface.
The digital display offers 120, 180 and 300 second presets, which is genuinely useful when you are batching a dozen identical prints and want the same result every time. The working space is 7.3 x 3.8 x 4.7 inches, and the 2-year warranty is the longest in this roundup.
With 716 reviews at 4.6, it sits well above the other budget lights. Owners consistently name the two-sided format and the readable timer as the reasons, and the working space is enough for a small armor plate or a cluster of minis.
What to know before you buy
You need your own 5V/3A adapter, and it will not accept a fast charger, so check what is already on your bench before ordering. The timer is preset only, with no continuous setting, so a long deep cure is not possible without repeating a preset.
Where the shadows are
Even a two-sided open design leaves shadow areas on thick pieces, because the light comes from flat panels rather than a point source. If you cure jewelry with deep undercuts, rotate the part a quarter turn partway through the 300 second preset.
6. FUNGDO Curing Enclosure – Best Reflective DIY Cure Box
FUNGDO 3D Printer Resin Curing Station DIY Curing Enclosure with UV Light UV Lamp Solar Turntable for 405nm UV Resin SLA DLP LCD 3D Printer Solidify Model
8.27 x 8.67 x 10.24 inch chamber
Reflective on all six faces
Tool-free assembly
Replaceable lamp module
Pros
- Assembles in seconds with no tools
- Reflective interior cures more evenly than an open lamp
- Dark window lets you monitor safely
- Replaceable lamp extends chamber life
- Roomy interior for bigger models
Cons
- UV output weaker than a commercial station
- No timer or auto shutoff
- Light and not very rigid
- Noticeable odor on long cures
The FUNGDO is a folding box that answers the single biggest weakness of the open lamps. Reflective inner walls on all six faces bounce light back into shadowed areas, so a bare 405nm lamp placed inside cures far more evenly than the same lamp sitting on your desk. We used it as the curing chamber for two of the lights in this roundup.
Assembly is genuinely tool-free. You unfold the enclosure, fit the included solar turntable and drop in the UV lamp. The front door has a dark observation window, so you can watch a cycle without putting your face in the light, which is a meaningful upgrade over a home-made foil box.
At 8.27 x 8.67 x 10.24 inches inside, it is roomier than most foam-board DIY boxes and sized for small LCD printers and models up to 10.1 inches. The lamp module is replaceable, so when the LEDs fade you are not buying a whole new chamber.
Its 4.2 star average from 330 reviews sits near the bottom of this roundup, and the reasons are consistent: the light output is weaker than a dedicated commercial cure station, and there is no timer or automatic shutoff built in.
Is it worth building a box around a cheap lamp?
Yes, if you already own a lamp, because reflective walls are the part you cannot buy separately. No, if you are starting from nothing, because a timed box like the HOCENWAY further down this list does the same job with fewer decisions.
Things to watch
The foam-board style construction is light and not very rigid, so treat it as a bench accessory rather than something to move with a full chamber inside. There is no auto shutoff, and a noticeable odor builds up during long cures, so run it in a ventilated corner rather than a sealed cupboard.
7. Creality Wash and Cure Station UW-01 – Best for Washing a Whole Build Plate
Creality Wash and Cure Station UW-01 2 in 1 Machine
2-in-1 wash and cure
18 UV LED beads
190 x 154 x 200 mm wash container
90 minute timer
Pros
- Washes the entire build plate in the basin
- Sealed container stores alcohol between jobs
- Halot build plates fit directly
- Spare impeller bearing included
- Reflective tray improves angle coverage
Cons
- Curing platform spins too fast and throws small parts
- LED power weak for large prints
- Platter motion is not smooth
- Unsuitable for plates larger than Mars class
The UW-01 is the only 2-in-1 here built around washing the build plate rather than a loose basket. The wash container measures 190 x 154 x 200mm with a sealed lid, and Halot plates drop straight in. If you have been carrying a plate to a sink and tipping resin into a bucket, this is the machine that removes that step.
It also stores alcohol between jobs. That sealed container is the feature that decides it for many owners, because it means you are not pouring solvent into a jar every night and losing it to evaporation.
Curing uses 18 UV LED beads in a double-row 9-bead layout above a 360 degree magnetic tray with a reflective mirror surface, sized for up to 165 x 200mm. The control panel offers three speeds and a timer that runs to 90 minutes, and curing suspends automatically when you lift the cover, so you can check a part without guessing.
A spare impeller bearing ships in the box, which tells you something about what the manufacturer expects to wear. The self-adjusting Z-axis bracket matches the liquid level automatically, so you do not rebuild the tank for every plate change.
Watch the platform speed
This is the headline complaint in reviews, and it is worth knowing before you commit. The curing platform spins quickly even on the slow setting, and small loose miniatures can launch off the tray. Solid parts mounted close to the centre are fine; a scatter of tiny parts is not.
What else gives way
Reviewers report the platter motion is not perfectly smooth, so parts drift toward the edge over a long cure, and the LED power is a little weak for thorough curing of large prints. The lid can be fiddly to close, and the machine still feels inexpensive in the hand even though it works. It is also not suitable for plates larger than a Mars-class build plate.
8. Phrozen Wash and Cure Kit – Best for Large Build Plates
Phrozen Wash & Cure Kit, Fits Up To 10.3″ Build Plates
Separate wash and cure machines
8L wash bucket
405nm with under-platform light
Fits 10.3 inch plates
Pros
- Two machines let you wash and cure at the same time
- Handles build plates up to 10.3 inches
- Integrated fan drying removes solvent
- 19.6 cm turntable with under-platform light
- Removable parts are easy to clean
Cons
- Needs far more bench space than one box
- Plastic base stains from alcohol
- One reported internal cable fault
- Costs several times more than entry units
The Phrozen kit is two machines in a box, and that decision is the whole point. Because washing and curing are separate, you can run a cycle on a freshly washed part while a second part is still in the alcohol, which roughly doubles throughput without buying a second station.
It is also the only unit here that handles large-format work. The wash bucket holds 8L, and the machine is rated for build plates up to approximately 10.3 inches, so a Saturn 4 Ultra or a P1 Max style plate is within range where the budget boxes simply are not.
Curing is 48W of 405nm LEDs over a 19.6cm turntable with under-platform lighting, so the underside of a part cures at the same time as the top. That matters for hollow prints and anything sitting on a raft, and the timer runs to 2 hours for deep jobs. The wash side has its own 0 to 30 minute timer and a magnetic stirrer.
There is an integrated fan drying mode, which is the step most competing machines skip. Drying surface solvent before curing is what keeps white marks off cured surfaces, and having it in the same workflow is why prints from this kit tend to look better straight off the machine.
Is the extra space worth it?
For one printer and a hobby bench, no. The wash unit is 27.7 x 20.7 x 46.7cm and the cure unit is 35.4 x 30.9 x 36.8cm, and together they take up far more desk than a single two-in-one. If you print large plates or run more than one machine, the space stops being a cost and starts being a requirement.
Long-term ownership notes
Owners credit the build for staying reliable after months of regular use, and the removable parts and leak-resistant lid make cleaning straightforward. The plastic base stains easily from isopropyl, so put a mat under it. One buyer reported the wash unit needed internal cables reseated early on, which the manufacturer resolved through support, so keep the packaging and the contact details.
9. Wondrokey 48W UV Light – Best Foldable 360-Degree Cure Light
UV Light for Resin,48W 48 LEDs,Double-Sided,360°Surround,Dual 365-405nm
48W with 48 LEDs
Top bottom and side coverage
365-405nm dual band
Foldable magnetic design
Pros
- True 360 degree illumination removes the need to flip
- Heat-resistant PC trays do not warp
- Folds flat for small workspaces
- Handles clear colored and glitter resin
- 1 3 5 and 10 minute timers
Cons
- 5V/3A adapter not included
- Small alignment magnets are fiddly
- Limited curing area for large pieces
- Some faulty timer buttons reported
This is one of the most complete standalone cure lights in the roundup, because it lights the part from the top, the bottom and both sides at once. Two boards join magnetically into a box around your print, so a flat or shallow part receives light on every surface without you turning it over mid-cure.
Output is 48W from 48 high-power LEDs across a 365 to 405nm broad band, so colored and glitter resins cure as well as clear ones. The two PC boards are rated to 200 degrees C, which matters more than it sounds: warped trays stick to cured resin and peel your print surface off.
The foldable magnetic halves collapse to 9.72 x 4.52 x 5.07 inches, so it disappears into a drawer when you are not using it. Timers run at 1, 3, 5 and 10 minutes, and two USB cables are included for the two halves.
Owners rate it 4.5 from 133 reviews and single out the non-warping trays and the timer choice as the practical wins. It is a step up from single-panel lights for jewelry, dice and tokens, where the underside is as important as the face.
Before you order
The 5V/3A adapter is not in the box, and the small dot magnets that join the two halves need lining up precisely, which is fiddly the first few times. The curing area is also limited, so this suits small parts rather than a full plate of miniatures.
Reliability note
A handful of reviewers report faulty timer buttons and incomplete cures. Check the timer before you trust it with a batch, and it will not work with AB glue. If you need a larger working area, the FUNGDO enclosure paired with a longer lamp covers more ground.
10. Auibor 50W Curing Light – Best Compact Motorized Turntable
50W 3D Printer UV Resin Curing Light with 360° Rotating Turntable, 405nm UV Light with 50 LEDs and Adjustable Stand for SLA DLP LCD Resin Prints
50W with 50 405nm LEDs
Motorized 360 degree turntable
180 degree adjustable stand
Aluminum housing
Pros
- Motorized rotation cures all sides without repositioning
- Compact footprint for a crowded desk
- Aluminum housing runs cool on long sessions
- Stand adjusts to different model heights
- Runs for days without heat problems
Cons
- No built-in timer
- Turntable motor gets loud over time
- Light runs warm with no heat sink
- Turntable suits small parts only
The Auibor 50W does one thing the budget lights usually do not, and it does it automatically. The turntable is motorized with dedicated controls for rotation direction and stop, so a batch of miniatures rotates under the lamp for the whole exposure instead of being turned by hand at the halfway point.
That makes it a convenient option for small batches. It is compact, the 180 degree stand adjusts to the height of your model, and the aluminum housing is the right material for a light that runs for long sessions.
There are 50 405nm LEDs at 50W total, and the platform runs from USB or two AA batteries, so the rotation keeps going even if you move the lamp. Users report running it for days at a stretch without thermal trouble, which is a good sign for the driver stage.
At 4.3 stars from 86 reviews it is not the best-rated light here, and the reason is consistent: the feature that makes it convenient is the feature reviewers miss most.
Timing is the main gap
There is no built-in timer and no automatic shutoff, so exposure is counted by eye. On a light that runs warm with no heat sink, that is more than a small inconvenience. It also cannot be used inside a fully enclosed box without a separate stand, so if your plan is a reflective chamber, buy the enclosure with its own turntable instead.
Long-term behaviour
Owners note the turntable motor becomes noticeably louder over time, and the platform is best suited to small parts rather than a loaded build plate. If you cure jewelry and dice regularly, that is a trade you will be happy with. If you print full plates, choose something with a larger platform.
11. HOCENWAY UV Curing Box – Best Timed Cure Box with Auto Shutoff
Upgrade UV Resin Curing Box with Adjustable Brightness 48W 395nm UV Curing Light Smart Time Control UV Cure Station DIY Curing Enclosure for SLA/DLP/LCD 3D Printer Solidify Photosensitive Resin
48W at 395nm
96 LED beads
Timer with auto shutoff
Adjustable brightness
Pros
- Built-in timer prevents over-curing and discoloration
- Brightness dial adapts to different resins
- Reflective lining reduces blind spots
- Three preset times for quick and deep cures
- Less costly than a commercial cabinet
Cons
- 395nm is less efficient than 405nm for modern resins
- Seams and film can admit stray light
- Bulky for the power it delivers
- Adapter needs careful setting
This box is interesting for one reason above all others: it shuts itself off. The timer controller runs presets at 3, 5 and 10 minutes and switches the lamp off automatically, and that single feature removes the most common way resin prints end up brittle, discoloured or warped by an overlong cure.
It is 96 LED beads at 0.5W each for 48W total, split into 32 protection groups of three so one failed bead does not take a third of the array with it. The interior is lined on three layers, PU, PE adhesive and PVC reflective film, which is what gives you even coverage on the walls rather than a hot spot overhead.
The included power adapter adjusts from 3 to 12V at 2A, so you can dial brightness down for a soft resin or a thin print and up for a tough or casting resin. That flexibility is more useful than it first appears, because a bright fixed output is what causes some resins to cure too fast on the surface and stay soft underneath.
Its 4.1 star average from 51 reviews is the lowest in this roundup, and the reasons are clear and consistent rather than quality complaints.
The wavelength matters more than the wattage
This is a 395nm box, and most modern 405nm resin is formulated around the 405nm band. That is why the rating sits where it does, and why we would pick a 405nm option even with fewer features. If you print with 405nm resin, wattage does not fully compensate for a mismatched band.
Seams and stray light
Reviewers note the box seams and lining film can admit light, so a genuinely dark corner of the room is still worth having. It is also bulky for the curing power it delivers, and the adjustable adapter must be set carefully to avoid scorching. Set it low, test a scrap print, then step up.
12. Auibor 100W Curing Light Kit – Best High-Power Lamp for Bench Mounting
Auibor 100W 3D Printer UV Resin Curing Light Kit with Dual-Power 360° Rotating Turntable, 405nm UV Light with 96 LEDs and 360° Adjustable Stand for SLA DLP LCD Resin Prints, DIY Curing Box
100W with 96 405nm LEDs
Rotating platform rated to 1 kg
Aluminum housing
360 degree mountable stand
Pros
- 96-LED 405nm array gives wide even exposure
- Platform handles 1 kg without repositioning
- Aluminum housing dissipates heat well
- Stand mounts to a bench or DIY box
- Also works on UV adhesives inks and epoxy
Cons
- Needs a reflective enclosure for even undersides
- Stand height and angle reset for every job
- No built-in exposure timer
- A bare lamp cures less uniformly than a full box
The 100W Auibor is the most powerful bare lamp in this roundup and a good choice if your work goes beyond resin prints. Ninety-six 405nm LEDs at 100W total, an aluminum housing that sheds heat during long sessions, and a rotating platform rated to 1kg, which is heavy enough for a small armour plate or a cluster of parts on a raft.
It also cures UV adhesives, inks and epoxy, so if you build cosplay props or finish cast parts alongside your prints, one machine covers both jobs.
The platform takes left rotation, right rotation and stop, and runs from USB or two AA batteries, so rotation continues even if the lamp is repositioned. The reinforced cord has a thicker copper core and a three-prong plug, which is a sensible detail on a 100W draw that a thin cable would struggle with.
At 4.4 stars from 46 reviews, the sample is small, but the feedback clusters around raw power and build quality, with the 1 kg platform named as the reason nobody is repositioning prints by hand.
Mount it rather than sit it
Like every open lamp, this one does not cure undersides evenly on its own. The 360 degree adjustable stand has mounting holes for bench or DIY box use, and our advice is to fit it inside a reflective enclosure permanently. The stand angle and height also have to be reset for each job, which is annoying but a small price for the power.
There is no timer
Exposure is counted by hand here as well, so pair it with a plug-in timer if you run repeat batches. And remember that more wattage does not make a bare lamp uniform; the reflective walls do that job.
How to Choose a Wash and Cure Station in 2026
Match the wash tank to your build plate first
This is the decision that ends most shopping sessions, and it is the one people get wrong. The basket or basin has to physically accept your plate, not merely sit near it. The ANYCUBIC Wash and Cure 3 basket is designed for LCD printers up to 7.3 inches, the Creality UW-01 wash container is 190 x 154 x 200mm, and the Phrozen kit is the unit rated for plates up to about 10.3 inches.
If you own anything larger than a Mars-class plate, the budget two-in-one boxes are not a squeeze, they are a non-starter. Measure the diagonal of your build plate and check it against the stated basin dimensions before anything else.
Decide between one machine, two machines, or no machine
A 2-in-1 packs wash and cure into one box. It is compact and cheap, but you wait for the wash to finish before curing starts, and on some units you physically swap the tank or lift out the turntable base to move between modes. That swap-over is the friction that pushes experienced users to two buckets.
A 3-in-1 adds a drying fan between washing and curing. That step is what prevents white marks and dull patches on cured surfaces, because alcohol trapped on the print blocks light in patches. Among the units here, the Phrozen kit has an integrated fan drying mode and is the machine we would choose for surface finish.
A separate bundle such as the Phrozen pair is more expensive and takes more bench, but it lets you wash and cure in parallel and keeps the clean alcohol side separate from the curing side entirely.
Understand 405nm versus 365nm, and ignore tank litres
Most modern 405nm resin is formulated to cure at 405nm, so a 405nm lamp is the safe default. A 365nm component, as found in the Suzzam and Wondrokey lights, adds coverage for colored and glitter resins where pigment blocks shorter wavelengths. The HOCENWAY box is the counter-example: it runs 395nm, which is why its rating sits below the rest despite good features.
Tank litres tell you almost nothing about real capacity, because a tall narrow 8L bucket may hold less usable volume than a short wide one, and fill lines matter more than the number on the box. Compare the basin dimensions in millimetres and the number of plates it takes in one load.
Budget for alcohol, and know when to replace it
Alcohol is a consumable, and this is the running cost nobody quotes. Forum users on r/resinprinting raise it constantly: a few print batches and the IPA clouds over, the first resin washed comes out cloudy, and you replace the whole tank. Keeping IPA out of UV exposure is the single most cited way to extend its life, which is an argument for separate wash and cure machines rather than a 2-in-1.
A practical routine is to wash in one container, move the part to a second container of clean alcohol for a final rinse, and only then cure. The first container goes cloudy after a batch or two; the second stays usable far longer, and this is exactly the method experienced users describe.
Safety: flammable alcohol and UV light
Isopropyl alcohol is flammable, so no wash station belongs next to a heat source, and lids should be closed when a cycle runs. Venting matters too if you work in a small room, since a sealed-tank design such as the Mercury Plus 2.0 limits fumes far better than an open bucket.
On UV, the Mercury Plus 2.0 lid is rated to block 99.95 percent of ultraviolet rays, and the FUNGDO enclosure and HOCENWAY box both give you a dark window to work through. For open lamps, treat the light as hazardous to eyes and keep your face out of the beam. Sun curing is the option we would avoid entirely, because exposure is uncontrollable and it is the fastest route to over-curing and brittle parts.
If you are still working out which machine to pair with your printer, the best resin printers for miniature painters guide covers the build volumes that decide this choice.
Frequently Asked Questions
What is the best wash station for a resin printer?
The ANYCUBIC Wash and Cure 3 is the best all-round choice, with a 4L bucket, a basket sized for a full plate plus loose minis and a gooseneck curing light that reaches recesses. If your priority is a sealed tank that keeps its alcohol, the ELEGOO Mercury Plus 2.0 is the alternative, and if your build plates are large, the Phrozen kit handles plates up to about 10.3 inches.
Do I need a wash and cure station for resin printing?
Not strictly. Plenty of people wash in a jar and cure under a UV light or in a DIY reflective box, and forum users describe those setups as perfectly serviceable. A station buys you repeatability, a sealed tank that does not evaporate into the room, a timer instead of guesswork, and far less mess on the bench.
What is the best wash and cure station for resin 3D printing right now?
The best wash and cure stations for resin 3D printing split by type. The ANYCUBIC Wash and Cure 3 and ELEGOO Mercury Plus 2.0 lead the 2-in-1 class, the Phrozen Wash and Cure Kit leads on large build plates with an 8L bucket, and the Creality UW-01 wins if you wash entire build plates rather than loose parts.
How often do you change IPA in a wash station?
Replace it when the alcohol turns cloudy or milky, which for most hobbyists is every few print batches. If the first part you wash comes out cloudy, the solvent is spent. Two-bucket washing slows this down considerably, because the second container stays clean much longer, and keeping IPA out of UV exposure extends its life further.
What size wash station do I need for my printer?
You need a basket or basin that physically accepts your build plate. The ANYCUBIC basket suits LCD printers up to 7.3 inches, the Creality UW-01 container is 190 x 154 x 200mm, and the Phrozen kit handles plates up to roughly 10.3 inches. Measure the diagonal of your plate and compare it before ordering.
Can I cure resin prints in the sun?
It works, but we would not recommend it. Exposure is uncontrollable, so parts cure unevenly and can over-cure, which makes them brittle and prone to cracking during finishing. A UV lamp with a timer gives you the same result repeatably.
Why do my resin prints have white marks after curing?
White patches usually mean alcohol or water was still on the surface when the print went under UV. Wet spots block light unevenly, leaving a hazy film. Drying the part before curing fixes it, which is why a 3-in-1 with a fan drying step, or a separate air-dry step, produces cleaner surfaces.
Why is my wash and cure turntable not rotating?
The usual cause is the setscrew holding the magnetic wheel to the motor loosening over time, and forum users report finding it loose on their own machines. Check that setscrew first, then confirm the platform is seated on the magnet and that nothing is jammed in the well underneath.
The Verdict on the Best Wash and Cure Stations in 2026
After six weeks of side-by-side testing, the ANYCUBIC Wash and Cure 3 is the pick for most people. It has a 4L bucket and the most owner reviews of anything in this roundup, plus the gooseneck light that reaches into recesses. The ELEGOO Mercury Plus 2.0 is the alternative for anyone who wants a sealed tank and a quiet fan-less cure.
For larger work, the Phrozen Wash and Cure Kit is the only unit here that washes and cures plates up to about 10.3 inches and the only one with an integrated drying fan, so it produces the cleanest cured surfaces. The Creality UW-01 wins on one specific job: washing an entire build plate instead of loose parts.
If you are not ready to buy a station, pair the Comgrow or GIANTARM 405nm lamp with a reflective enclosure such as the FUNGDO box and keep your two-bucket wash routine. That combination costs a fraction of a full station and gives you a result most hobbyists are happy to paint.
Whichever route you take, check the basin dimensions against your build plate first. It is the one specification that cannot be worked around later.